Nissan Maxima Service and Repair Manual: Precaution

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the SR and SB section of this Service Manual.

WARNING:

  • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
  • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SR section.
  • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

  • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.
  • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service.

Precaution for Liquid Gasket

REMOVAL OF LIQUID GASKET

  • After removing nuts and bolts, separate the mating surface using Tool and remove old liquid gasket.

Nissan Maxima. REMOVAL OF LIQUID GASKET

Tool number : KV10111100 (J-37228)

CAUTION: Be careful not to damage the mating surfaces.

  • Tap (1) Tool to insert it, and then slide it (2) by tapping on the side as shown.
  • In areas where Tool is difficult to use, use plastic hammer to lightly tap the parts, to remove it.

CAUTION: If for some unavoidable reason tool such as screwdriver is used, be careful not to damage the mating surfaces.

LIQUID GASKET APPLICATION PROCEDURE

Nissan Maxima. LIQUID GASKET APPLICATION PROCEDURE

  1. Remove old liquid gasket adhering to the liquid gasket application surface and the mating surface using scraper.
  • Remove liquid gasket completely from the groove of the liquid gasket application surface, bolts, and bolt holes.
  1. Thoroughly clean the mating surfaces and remove adhering moisture, grease and foreign materials.
  2. Attach liquid gasket tube to Tool.

Nissan Maxima. LIQUID GASKET APPLICATION PROCEDURE

Tool number : WS39930000 ( - )

  1. Apply liquid gasket without breaks to the specified location with the specified dimensions.

Nissan Maxima. LIQUID GASKET APPLICATION PROCEDURE

  • If there is a groove for the liquid gasket application, apply liquid gasket to the groove.
  • As for the bolt holes, normally apply liquid gasket inside the holes. Occasionally, it should be applied outside the holes.

    Make sure to read the text of Service Manual.

  • Within five minutes of liquid gasket application, install the mating component.
  • If liquid gasket protrudes, wipe it off immediately.
  • Do not retighten nuts or bolts after the installation.
  • After 30 minutes or more have passed from the installation, fill engine oil and engine coolant.

CAUTION: If there are more specific instructions in the procedures contained in this manual concerning liquid gasket application, observe them.

    Engine cooling system
    ...

    Preparation
    PREPARATION Special Service Tool The actual shapes of the tools may differ from those illustrated here Commercial Service Tool ...

    Other materials:

    Diagnosis system (AV control unit)
    Description The AV control unit diagnosis function starts up with multifunction switch operation and the AV control unit performs a diagnosis for each unit in the system during the on board diagnosis. Perform a CONSULT diagnosis if the on board diagnosis does not start, e.g., the s ...

    U1243 display unit
    DTC Logic Diagnosis Procedure 1.CHECK DISPLAY UNIT POWER SUPPLY AND GROUND CIRCUIT Check display unit power supply and ground circuit 2.CHECK CONTINUITY OF COMMUNICATION CIRCUIT Turn ignition switch OFF. Disconnect display unit connector M142 and AV control unit connector M163. ...

    Rear spoiler
    Exploded View Rear spoiler assembly High-mounted stop lamp harness connector Harness grommet Removal and Installation Removal Remove trunk lid finisher. Refer to INT-36, "Removal and Installation". Disconnect the harness connector (1) from the high-mounted stop lamp. Remo ...

    Nissan Maxima Owners Manual

    Nissan Maxima Service and Repair Manual

    © 2017-2019 Copyright www.nimainfo.com
    0.0113