Nissan Maxima Service and Repair Manual: Precaution

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the SR and SB section of this Service Manual.

WARNING:

  • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
  • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SR section.
  • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

  • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.
  • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery, and wait at least 3 minutes before performing any service.

Precaution for Work

  • When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
  • When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
  • Protect the removed parts with a shop cloth and prevent them from being dropped.
  • Replace a deformed or damaged clip.
  • If a part is specified as a non-reusable part, always replace it with a new one.
  • Be sure to tighten bolts and nuts securely to the specified torque.
  • After installation is complete, be sure to check that each part works properly.
  • Follow the steps below to clean components: - Water soluble dirt:
  • Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
  • Then rub with a soft, dry cloth.

    - Oily dirt:

  • Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
  • Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
  • Then rub with a soft, dry cloth.
    - Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
    - For genuine leather seats, use a genuine leather seat cleaner.
    Squeak and rattle trouble diagnoses
    Work Flow CUSTOMER INTERVIEW Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the ...

    Preparation
    Special Service Tool The actual shapes of the tools may differ from those illustrated here. Commercial Service Tools ...

    Other materials:

    Exhaust valve timing control
    System Diagram System Description INPUT/OUTPUT SIGNAL CHART *: This signal is sent to the ECM via the CAN Communication line. SYSTEM DESCRIPTION This mechanism magnetically controls cam phases continuously with the fixed operating angle of the exhaust valve. The ECM receives ...

    B260f engine status
    Description BCM receives the engine status signal from ECM via CAN communication. DTC Logic DTC DETECTION LOGIC NOTE: If DTC B260F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-29, "DTC Logic". If DTC B260F is displayed with D ...

    Front door speaker
    Description The AV control unit sends audio signals to the BOSE speaker amp. The BOSE speaker amp. amplifies the audio signals before sending them to the front door speakers using the audio signal circuits. Diagnosis Procedure 1.CONNECTOR CHECK Check the AV control unit, BOSE speaker amp. ...

    Nissan Maxima Owners Manual

    Nissan Maxima Service and Repair Manual

    © 2017-2024 Copyright www.nimainfo.com
    0.0062