Nissan Maxima Service and Repair Manual: Turn signal lamp circuit

Nissan Maxima Service and Repair Manual / Driver controls / Exterior lighting system / DTC/circuit diagnosis / Turn signal lamp circuit

Description

The BCM monitors inputs from the combination switch to determine when to activate the turn signals. The BCM outputs voltage direction to the left and right turn signals during turn signal operation or both during hazard warning operation. The BCM sends a turn signal indicator request to the combination meter via the CAN communication lines.

The BCM performs the fast flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is open.

NOTE: Turn signal lamp blinks at normal speed when using the hazard warning lamp.

Component Function Check

1.CHECK TURN SIGNAL LAMP

CONSULT

  1. Select "FLASHER" of BCM (FLASHER) active test item.
  2. While operating the test item, check that the turn signal lamp blinks.

LH : Turn signal lamp LH blinking
RH : Turn signal lamp RH blinking
OFF : The turn signal lamp OFF

Diagnosis Procedure

1.CHECK TURN SIGNAL LAMP BULB

Check the applicable lamp bulb to be sure the proper bulb standard is in use and the bulb is not open.

2.CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

  1. Turn the ignition switch OFF.
  2. Disconnect front combination lamp connector, door mirror connector (if equipped with turn signal in mirror) and rear combination lamp connector.
  3. Turn the ignition switch ON.
  4. With turn signal switch operating, check the voltage between the front combination lamp harness connector and ground.
  5. With turn signal switch operating, check the voltage between the rear combination lamp harness connector and ground.
  6. With turn signal switch operating, check the voltage between the door mirror (if equipped with turn signals in the mirrors) harness connector and ground.

Nissan Maxima. CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

Nissan Maxima. CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

Nissan Maxima. CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

Nissan Maxima. CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

3.CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN

Nissan Maxima. CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN

Nissan Maxima. CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN

Nissan Maxima. CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN

  1. Turn ignition switch OFF.
  2. Disconnect BCM connector M17.
  3. Check continuity between the BCM harness connector (A) and the front combination lamp connector (B).
  4. Check continuity between the BCM harness connector (A) and the rear combination lamp harness connector (B)
  5. Check continuity between the BCM harness connector (A) and the door mirror connector (B) (if equipped with turn signal in mirror).

Nissan Maxima. CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN

Nissan Maxima. CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN

Nissan Maxima. CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN

4.CHECK TURN SIGNAL LAMP SHORT CIRCUIT

Nissan Maxima. CHECK TURN SIGNAL LAMP SHORT CIRCUIT

Check continuity between the BCM harness connector and ground.

Nissan Maxima. CHECK TURN SIGNAL LAMP SHORT CIRCUIT

5.CHECK TURN SIGNAL LAMP GROUND CIRCUIT

Nissan Maxima. CHECK TURN SIGNAL LAMP GROUND CIRCUIT

Nissan Maxima. CHECK TURN SIGNAL LAMP GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2. Check continuity between the front combination lamp and ground.
  3. Check continuity between the rear combination lamp and ground.
  4. Check continuity between the door mirror and ground (if equipped with turn signal in mirror).

Nissan Maxima. CHECK TURN SIGNAL LAMP GROUND CIRCUIT

Nissan Maxima. CHECK TURN SIGNAL LAMP GROUND CIRCUIT

Nissan Maxima. CHECK TURN SIGNAL LAMP GROUND CIRCUIT

    Parking lamp circuit
    Description The IPDM E/R (intelligent power distribution module engine room) controls the tail lamp relay based on inputs from the BCM over the CAN communication lines. When the tail lamp relay i ...

    Optical sensor
    Description The optical sensor converts the outside brightness (lux) to voltage and transmits the optical sensor signal to the BCM. Component Function Check 1.CHECK OPTICAL SENSOR SIGNAL BY CONSU ...

    Other materials:

    RGB (R: red) signal circuit
    Description Transmit the image displayed with AV control unit with RGB signal to the display unit. Diagnosis Procedure 1.CHECK CONTINUITY RGB (R: RED) SIGNAL CIRCUIT Turn ignition switch OFF. Disconnect display unit connector M141 and AV control unit connector M117. Check continu ...

    P0452 evap control system pressure sensor
    Description The EVAP control system pressure sensor detects pressure in the purge line. The sensor output voltage to the ECM increases as pressure increases. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously ...

    TCM branch line circuit
    Diagnosis Procedure 1.CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side). TCM Harness connector F1 Harness con ...

    Nissan Maxima Owners Manual

    Nissan Maxima Service and Repair Manual

    © 2017-2026 Copyright www.nimainfo.com
    0.0064