Nissan Maxima Service and Repair Manual: Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT
PRE-TENSIONER", used along with a front seat belt, helps to reduce the risk
or severity of injury to the driver and front passenger for certain types of
collision. This system includes seat belt switch inputs and dual stage front air
bag modules. The SRS system uses the seat belt switches to determine the
front air bag deployment, and may only deploy one front air bag, depending on
the severity of a collision and whether the front occupants are belted or
unbelted.
Information necessary to service the system safely is included in
the SR and SB section of this Service Manual.
WARNING:
- To avoid rendering the SRS inoperative, which could increase
the risk of personal injury or death in the event of a collision which
would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
- Improper maintenance, including incorrect removal and
installation of the SRS, can lead to personal injury caused by
unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SR section.
- Do not use electrical test equipment on any circuit related to
the SRS unless instructed to in this Service Manual. SRS wiring harnesses
can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
- When working near the Airbag Diagnosis Sensor Unit or other
Airbag System sensors with the Ignition ON or engine running, DO NOT use
air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration could activate the sensor(s) and deploy the air bag(s),
possibly causing serious injury.
- When using air or electric power tools or hammers, always
switch the Ignition OFF, disconnect the battery, and wait at least 3
minutes before performing any service.
Precaution for Seat Belt Service
CAUTION:
- Before removing the front seat belt pre-tensioner assembly,
turn the ignition switch off, disconnect both battery cables and wait at
least 3 minutes.
- Do not use electrical test equipment for front seat belt
pre-tensioner connector.
- After replacing or reinstalling front seat belt pre-tensioner
assembly, or reconnecting front seat belt pre-tensioner connector, check
the system function. Refer to SRC-12, "SRS Operation Check".
- Do not disassemble buckle or seat belt assembly.
- Replace anchor bolts if they are deformed or worn out.
- Do not oil tongue and buckle.
- If any component of seat belt assembly is questionable, do not
repair. Replace the whole seat belt assembly.
- If webbing is cut, frayed, or damaged, replace seat belt
assembly.
- When replacing seat belt assembly, use a genuine NISSAN seat
belt assembly.
COMPONENT INSPECTION
Inspection
AFTER A COLLISION
WARNING: Inspect all seat belt assemblies
including retractors and attaching hardware after any collision.
NISSAN/INFINITI recommends that all s ...
Other materials:
B260f engine status
Description
BCM receives the engine status signal from ECM via CAN
communication.
DTC Logic
DTC DETECTION LOGIC
NOTE:
If DTC B260F is displayed with DTC
U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-29, "DTC Logic".
If DTC B260F is displayed with D ...
U121D AV control unit
DTC Logic
Diagnosis Procedure
1.CHECK PLAYBACK OF A DISK (CD)
U121E AV CONTROL UNIT
DTC Logic
Diagnosis Procedure
1.CHECK PLAYBACK OF A DISK (CD)
U1225 AV CONTROL UNIT
DTC Logic
DTC DETECTION LOGIC
U1227 AV CONTROL UNIT
DTC Logic
Diagnosis Procedure
1.CHECK PLAYBACK OF A ...
SRS air bag system
"AIR BAG" Warning Lamp Does Not Turn Off
DIAGNOSTIC PROCEDURE
1.CHECK CONDITION OF AIR BAG MODULE
Inspect for any deployed air bag modules or seat belt pre-tensioners.
2.CHECK THE AIR BAG FUSE
Check 10A fuse [No. 2, located in the fuse block (J/B)].
3.CHECK AIR BAG FUSE AGAIN
Replace 10A fuse ...