Nissan Maxima Service and Repair Manual: B1118 - B1120 satellite sensor LH

Description

DTC B1118 - B1120 SATELLITE SENSOR LH

The satellite sensor LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will
monitor the satellite sensor LH for internal failures and its circuits for communication errors.

PART LOCATION

DTC Logic

DTC DETECTION LOGIC

With CONSULT

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.CHECK SELF-DIAG RESULT

  1. Turn ignition switch ON.
  2. Check for DTC using CONSULT.

2.ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.CHECK SELF-DIAG RESULT

  1. Turn ignition switch ON.
  2. Check the air bag warning lamp status. Refer to SRC-14, "Trouble Diagnosis without CONSULT".

NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.

Diagnosis Procedure

1.HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal
  • Loose terminal
  • Poor connection

NOTE:
All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).

2.CONFIRM DTC

  1. Reconnect all harness connectors.
  2. Turn ignition switch ON.
  3. Check for DTC using CONSULT.

3.WIRING HARNESS

Check the wiring harness for visible damage.

NOTE:
The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component
(including any in-line connectors).

4.CONFIRM DTC

  1. Reconnect all harness connectors.
  2. Turn ignition switch ON.
  3. Check for DTC using CONSULT.

5.AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace the air bag diagnosis sensor unit. Refer to SR-31, "Removal and Installation".
  2. Turn ignition switch ON.
  3. Check for DTC using CONSULT.

6.LH SIDE AIR BAG SATELLITE SENSOR

  1. Replace the LH side air bag satellite sensor. Refer to SR-29, "Removal and Installation".
  2. Turn ignition switch ON.
  3. Check for DTC using CONSULT.

7.RELATED HARNESS

Replace the related harness.

    B1033 - B1035 crash zone sensor
    Description DTC B1033 - B1035 CRASH ZONE SENSOR The crash zone sensor is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit willmonitor for opens and shorts in detected ...

    B1113 - B1115 satellite sensor RH
    Description DTC B1113 - B1115 SATELLITE SENSOR RH The satellite sensor RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit willmonitor the satellite sensor RH for ...

    Other materials:

    Filament
    Inspection and Repair INSPECTION When measuring voltage, wrap tin foil around the top of the negative probe. Then press the foil against the wire with your finger. Attach probe circuit tester (in Volt range) to middle portion of each filament. If a filament is burne ...

    Drive Belts
    Checking Drive Belts Idler pulley Drive belt Power steering oil pump Drive belt auto-tensioner Crankshaft pulley Idler pulley A/C compressor Generator Indicator New drive belt range Possible use range View D Engine front WARNING: Inspect and check the dri ...

    P1800 vias control solenoid valve 1
    Description The VIAS control solenoid valve 1 cuts the intake manifold vacuum signal for power valve 1 control. It responds to ON/OFF signals from the ECM. When the solenoid is OFF, the vacuum signal from the intake manifold is cut. When the ECM sends an ON signal the coil pulls the plunger ...

    Nissan Maxima Owners Manual

    Nissan Maxima Service and Repair Manual

    © 2017-2026 Copyright www.nimainfo.com
    0.0055