Nissan Maxima Service and Repair Manual: Rear combination lamp
Exploded View
- Slide clip
- Grommets
- Rear combination lamp
Removal and Installation
REAR COMBINATION LAMP
Removal
- Remove the trunk side finisher. Refer to INT-36, "Removal and Installation".
- Remove the rear combination lamp nuts.
- Pull the rear combination lamp toward the rear of the vehicle to remove it.
- Disconnect the harness connector from the rear combination lamp.
Installation
Installation is in the reverse order of removal.
WARNING: Do not touch bulb with your hand while it is on or right after being turned off, a burn injury may result.
CAUTION:
- Do not touch bulb glass with your hand or keep other grease and oily substances away from bulb glass.
- Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP
Replacement is integral with rear combination lamp. Refer to EXL-162, "Exploded View".
REAR SIDE MARKER LAMP BULB
Removal
- Remove the rear combination lamp. Refer to EXL-162, "Exploded View".
- Rotate the rear side marker lamp socket counterclockwise and unlock from rear combination lamp.
- Remove the bulb from the rear side marker lamp socket.
Installation
Installation is in the reverse order of removal.
REAR TURN SIGNAL LAMP BULB
Removal
- Remove the rear combination lamp. Refer to EXL-162, "Exploded View".
- Rotate the rear turn signal lamp socket counterclockwise and unlock from rear combination lamp.
- Remove the bulb from the rear turn signal lamp socket.
Installation
Installation is in the reverse order of removal.
BACK-UP LAMP BULB
Removal
- Remove the rear combination lamp. Refer to EXL-162, "Exploded View".
- Rotate the back-up lamp socket counterclockwise and unlock from rear combination lamp.
- Remove the bulb from the back-up lamp socket.
Installation
Installation is in the reverse order of removal.
Hazard switch
Exploded View
Hazard switch
Cluster lid D
Removal and Installation
REMOVAL
Remove cluster lid D. Refer to IP-18, "Removal and Installation".
Disconnect the harness connector from th ...
High-mounted stop lamp
Exploded View
Models Without Rear Spoiler
High-mounted stop lamp cover
High-mounted stop lamp bulb
Models With Rear Spoiler
Rear spoiler
High-mounted stop lamp assembly
Re ...
Other materials:
ECU diagnosis information
A/C AUTO AMP
Reference Value
VALUES ON THE DIAGNOSIS TOOL
CONSULT MONITOR ITEM
A/C AUTO AMP. HARNESS CONNECTOR TERMINAL LAYOUT
TERMINALS AND REFERENCE VALUES FOR A/C AUTO AMP.
Fail-Safe
FAIL-SAFE FUNCTION
If a communication error exists between the A/C auto amp., the AV
...
Blower motor control system
System Diagram
System Description
Fan speed is automatically controlled by the temperature setting, ambient
temperature, in-vehicle temperature,
intake temperature, amount of sunload and air mix door position.
By pressing the AUTO switch, the blower motor starts to gradually increase
a ...
RCTA system operation
1. Side BSW/RCTA Indicator Light
2. BSW/RCTA Indicator
The RCTA system can help alert the driver of an
approaching vehicle when the driver is backing
out of a parking space.
When the shift position is in R (Reverse) and the
vehicle speed is less than approximately 5 mph
(8 km/h), the RC ...
Nissan Maxima Owners Manual
- Illustrated table of contents
- Safety-Seats, seat belts and supplemental restraint system
- Instruments and controls
- Pre-driving checks and adjustments
- Monitor, climate, audio, phone and voice recognition systems
- Starting and driving
- In case of emergency
- Appearance and care
- Do-it-yourself
- Maintenance and schedules
- Technical and consumer information
Nissan Maxima Service and Repair Manual
0.0066