Nissan Maxima Service and Repair Manual: BCM (body control module)

Reference Value

NOTE: The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS transmitter IDs
  • Display tire pressure reported by the TPMS transmitter
  • Read TPMS DTCs
  • Register TPMS transmitter IDs
  • Check Intelligent Key relative signal strength
  • Confirm vehicle Intelligent Key antenna signal strength

VALUES ON THE DIAGNOSIS TOOL

Nissan Maxima. VALUES ON THE DIAGNOSIS TOOL

Nissan Maxima. VALUES ON THE DIAGNOSIS TOOL

Nissan Maxima. VALUES ON THE DIAGNOSIS TOOL

Nissan Maxima. VALUES ON THE DIAGNOSIS TOOL

Nissan Maxima. VALUES ON THE DIAGNOSIS TOOL

Terminal Layout 

Nissan Maxima. Terminal Layout  

Nissan Maxima. Terminal Layout  

Nissan Maxima. Terminal Layout  

Nissan Maxima. Terminal Layout  

Nissan Maxima. Terminal Layout  

Nissan Maxima. Terminal Layout  

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Nissan Maxima. Terminal Layout 

Fail Safe 

Nissan Maxima. Fail Safe 

Nissan Maxima. Fail Safe 

DTC Inspection Priority Chart

If some DTCs are displayed at the same time, perform inspections one by one based on the following priority chart.

Nissan Maxima. DTC Inspection Priority Chart

Nissan Maxima. DTC Inspection Priority Chart

DTC Index

NOTE: Details of time display

  • CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning ignition switch OFF → ON again.
  • 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases 1 → 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch OFF → ON after returning to the normal condition if the malfunction is detected again.

Nissan Maxima. DTC Index

Nissan Maxima. DTC Index

Nissan Maxima. DTC Index

    Automatic drive positioner control unit
    Reference Value TERMINAL LAYOUT PHYSICAL VALUES ...

    Wiring diagram
    AUTOMATIC DRIVE POSITIONER Wiring Diagram ...

    Other materials:

    Main line between HVAC and ABS circuit
    Diagnosis Procedure 1.CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side). Harness connector M1 Harness connect ...

    Power supply and ground circuit
    BCM (BODY CONTROL MODULE) BCM (BODY CONTROL MODULE) : Diagnosis Procedure 1. CHECK FUSE AND FUSIBLE LINK Check if the following BCM fuses or fusible link are blown. 2. CHECK POWER SUPPLY CIRCUIT Turn ignition switch OFF. Disconnect BCM. Check voltage between BCM harness connector and ...

    Active trace control
    The Integrated Dynamics-control Module is an electric control module that includes the following functions: Active Trace Control Active Engine Brake Active Ride Control This system senses driving based on the driver's steering and acceleration/braking patterns, and controls brake pres ...

    Nissan Maxima Owners Manual

    Nissan Maxima Service and Repair Manual

    © 2017-2025 Copyright www.nimainfo.com
    0.007