Nissan Maxima Service and Repair Manual: Removal and installation

  • Audio unit
  • Removal and Installation Audio unit brackets (LH/RH) A/C auto amp. Cluster lid C lower Audio unit Clip Pawl REMOVAL Disconnect the battery negative terminal. Refer to PG-67, "Removal and Installation (Battery)". Remove cluster lid D. Refer to IP-11, "Removal and Installation". Remove cluster lid C lower finisher (1).   : Pawl : Clip   Remove the audio unit screws (A) and cluster lid C screws (B). Pull out the audio unit, disconnect the harness connector from the audio unit and remove. INSTALLATION Installation is in the reverse order of removal.

  • Audio display unit
  • Removal and Installation Audio display unit Audio & A/C display unit bracket A/C display unit Front cover REMOVAL Disconnect the battery negative terminal. Refer to PG-67, "Removal and Installation (Battery)". Remove cluster lid D. Refer to IP-11, "Removal and Installation". Remove the audio & A/C display unit bracket screws (A). Pull out the audio & A/C display unit assembly (1), disconnect the harness connectors from the audio display unit and remove. Remove the front cover, then disconnect the audio display unit connectors and remove the audio display unit from the audio/A/C display unit brackets. INSTALLATION Installation is in the reverse order of removal.

  • Front tweeter
  • Removal and Installation REMOVAL Remove the front pillar finisher. Refer to IP-10, "Exploded View". Remove the front tweeter speaker grille. Refer to IP-10, "Exploded View". Remove the front tweeter speaker screws (A). Pull out front tweeter speaker (1), disconnect the harness connector from the front tweeter speaker and remove. INSTALLATION Installation is in the reverse order of removal.

  • Front door speaker
  • Removal and Installation REMOVAL Remove the front door finisher. Refer to INT-18, "Removal and Installation". Remove the front door speaker screws (A). Disconnect the harness connector from the front door speaker (1) and remove. Remove the front door speaker spacer screws (B) and remove the front door speaker spacer (2). INSTALLATION Installation is in the reverse order of removal.

  • Rear door speaker
  • Removal and Installation REMOVAL Remove the rear door finisher. Refer to INT-21, "Removal and Installation". Remove the rear door speaker screws (A). Disconnect the harness connector (B) from the rear door speaker (1) and remove. INSTALLATION Installation is in the reverse order of removal.

  • Subwoofer
  • Removal and Installation Subwoofer (LH) Subwoofer (RH)  Subwoofer screws Subwoofer connectors REMOVAL Remove the rear parcel shelf finisher. Refer to INT-28, "Removal and Installation". Remove the subwoofer screws. Pull out the subwoofer, disconnect the harness connector from the subwoofer and remove. INSTALLATION Installation is in the reverse order of removal.

  • Subwoofer AMP
  • Removal and Installation Subwoofer amp. and bracket Subwoofer amp. bracket screws REMOVAL Disconnect the battery negative terminal. Refer to PG-67, "Removal and Installation (Battery)". Remove the parcel shelf finisher. Refer to INT-28, "Removal and Installation". NOTE: The subwoofer amp. can be removed without removing the parcel amp finisher. If moving the subwoofer amp. and bracket, it is necessary to remove the parcel shelf finisher. Remove the trunk upper finisher. Refer to INT-36, "Exploded View". Remove the subwoofer amp. screws. Disconnect the harness connectors from the subwoofer amp. and remove. INSTALLATION Installation is in the reverse order of removal.

  • Steering switch
  • Removal and Installation REMOVAL Remove the driver airbag module. Refer to SR-12, "Removal and Installation". Remove the steering wheel audio control switch screws (A). Release the steering wheel audio control switch harness clips (B). Remove the steering wheel audio control switches (1). INSTALLATION Installation is in the reverse order of removal.

  • Audio antenna
  • Location of Antenna Audio unit Audio unit antenna feeder In-line connectors M103, M501 Antenna amp. Window antenna Window Antenna Repair ELEMENT CHECK Attach probe circuit tester (ohm setting) to antenna terminal on each side When measuring continuity, wrap tin foil around the top of probe. Then, press the foil against the wire with your finger. If an element is broken, no continuity will exist. To locate a break, move probe along element. Tester indication will change abruptly when probe passes the broken point REPAIR EQUIPMENT Conductive silver composition (DuPont No. 4817 or equivalent) Ruler 30 cm (11.

  • Antenna AMP
  • Removal and Installation REMOVAL Remove the rear pillar finisher RH. Refer to INT-23, "Exploded View". Detach the antenna amp. harness clip (A). Disconnect the harness connectors (B) from the antenna amp. (1). Remove the antenna amp. screw (C) and the antenna amp. (1). INSTALLATION Installation is in the reverse order of removal.

  • Microphone
  • Removal and Installation REMOVAL Remove the front room/map lamp assembly. Refer to INL-84, "Removal and Installation". Detach the microphone connector (A). Remove the front room/map lamp covers (1), then remove the map lamp assembly cover (2). Release the microphone tabs (A), then remove the microphone (1). INSTALLATION Installation is in the reverse order of removal.

  • Tel antenna
  • Removal and Instalation REMOVAL Disconnect the battery negative terminal. Refer to PG-67, "Removal and Installation (Battery)". Remove the rear parcel shelf finisher. Refer to INT-28, "Removal and Installation". Remove the Bluetooth antenna screw (A). Detach the Bluetooth antenna harness clip (B). Fold down the rear seat (if equipped) or open the trunk lid, then detach the Bluetooth antenna harness clip (C). Disconnect the harness connector (D) from the Bluetooth antenna (1) and remove. INSTALLATION Installation is in the reverse order of removal.

  • Bluetooth control unit
  • Removal and Installation REMOVAL Disconnect the battery negative terminal. Refer to PG-67, "Removal and Installation (Battery)". Remove the trunk upper finisher. Refer to INT-23, "Exploded View". Remove the parcel shelf finisher. Refer to INT-28, "Removal and Installation". From inside the passenger compartment, remove the Bluetooth control unit bracket screws. From inside the trunk, disconnect the Bluetooth control unit connectors (B) and remove the Bluetooth control unit and bracket assembly. Remove the Bluetooth control unit bracket screws (A) to remove the Bluetooth control unit from the Bluetooth control unit brackets. INSTALLATION Installation is in the reverse order of removal.

Preparation

Audio unit