Nissan Maxima Service and Repair Manual: Removal and installation
- AV control unit
- Multifunction switch
- Audio display unit
- USB connector
- Aux in jack
- Front tweeter
- Front door speaker
- Rear door speaker
- Subwoofer
- Subwoofer AMP
- Bose speaker AMP
- Satellite radio tuner
- Satellite radio antenna
- Steering switch
- Audio antenna
- Antenna AMP
- Microphone
- Tel antenna
- Bluetooth control unit
- Rear view camera
Removal and Installation AV control unit AV control unit bracket LH AV control unit bracket RH A/C auto amp. Cluster lid C (with A/C and AV switch assembly attached) Clip AV CONTROL UNIT Removal CAUTION: Before replacing AV control unit, perform "READ CONFIGURATION" to save current vehicle specification. Refer to AV-180, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement". Disconnect the battery negative terminal. Remove the cluster lid D. Refer to IP-11, "Removal and Installation". Remove the cluster lid C Remove the av control unit screws (A), then pull out the av control unit (1), disconnect the av control unit connectors and remove the av control unit (1).
Removal and Installation REMOVAL Remove cluster lid D. Refer to IP-10, "Exploded View". Remove the four multifunction switch screws (A) and remove the multifunction switch (2) from cluster lid D (1). : Metal clip INSTALLATION Installation is in the reverse order of removal.
Removal and Installation Audio display unit bracket Audio display unit Cluster lid D Multifunction switch Audio display unit bracket screws Audio display unit screws Metal Clip REMOVAL Remove the cluster lid D. Refer to IP-11, "Removal and Installation". Remove the audio display unit bracket screws (A). Pull out the audio display unit and bracket assembly (1). Disconnect the harness connectors from the audio display unit and bracket assembly (1) and remove. Remove the audio display unit screws on the sides and remove the audio display unit from the audio display unit brackets. INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Remove the center console assembly. Refer to IP-14, "Removal and Installation". Release the pawl from the back of the center console to remove the USB interface (1). INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Remove the center console. Refer to IP-14, "Removal and Installation". Remove the center console bin box. Remove the auxiliary input jacks screws (A), then remove the auxiliary input jacks (1). INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Remove the front pillar finisher. Refer to INT-24, "Removal and Installation". Remove the front tweeter speaker grille. Refer to IP-10, "Exploded View". Remove the front tweeter speaker screws (A). Pull out front tweeter speaker (1), disconnect the harness connector from the front tweeter speaker and remove INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Remove the front door finisher. Refer to INT-18, "Removal and Installation". Remove the front door speaker screws (A). Disconnect the harness connector from the front door speaker (1) and remove. Remove the front door speaker spacer screws (B) and remove the front door speaker spacer (2). INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Remove the rear door finisher. Refer to INT-21, "Removal and Installation". Remove the rear door speaker screws (A). Disconnect the harness connector (B) from the rear door speaker (1) and remove. INSTALLATION Installation is in the reverse order of removal.
Removal and Installation Subwoofer LH Subwoofer RH Subwoofer screws Subwoofer connectors REMOVAL Remove the rear parcel shelf finisher. Refer to INT-36, "Removal and Installation". Remove the subwoofer screws. Pull out the subwoofer, disconnect the harness connector from the subwoofer and remove. INSTALLATION Installation is in the reverse order of removal.
Removal and Installation Subwoofer amp. and bracket Subwoofer amp. bracket screws REMOVAL Disconnect the battery negative terminal. Refer to PG-67, "Removal and Installation (Battery)". Remove the parcel shelf finisher. Refer to INT-28, "Removal and Installation". NOTE: The subwoofer amp. can be removed without removing the parcel amp finisher. If moving the subwoofer amp. and bracket, it is necessary to remove the parcel shelf finisher. Remove the trunk upper finisher. Refer to INT-36, "Exploded View". Remove the subwoofer amp. screws. Disconnect the harness connectors from the subwoofer amp. and remove. INSTALLATION Installation is in the reverse order of removal.
Removal and Installation Bose speaker amp. Screws REMOVAL NOTE: If removing the BOSE speaker amp. bracket, it is necessary to remove the parcel shelf finisher. The BOSE speaker amp. can be removed without removing the BOSE speaker amp. bracket. Disconnect the battery negative terminal. Remove the trunk upper finisher. Refer to INT-36, "Exploded View". Remove the Bose speaker amp. screws. Disconnect the Bose speaker amp. connectors and remove the Bose speaker amp. INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Disconnect the battery negative terminal. Remove the trunk upper finisher. Refer to INT-36, "Exploded View". Remove the parcel shelf finisher. Refer to INT-28, "Removal and Installation". From inside the passenger compartment, remove the bracket screws and lower the assembly for access. Remove the satellite radio tuner unit screws (A), disconnect the harness connectors (B) from the satellite radio tuner (1) and remove. INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Lower the headlining at the rear. Refer to INT-33, "Exploded View". Disconnect the harness connector (A) from satellite radio antenna. Remove the satellite radio antenna nut (B) and the satellite radio antenna (1). INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Remove the driver airbag module. Refer to SR-12, "Removal and Installation". Remove the steering wheel audio control switch screws (A). Release the steering wheel audio control switch harness clips (B). Remove the steering wheel audio control switches (1). INSTALLATION Installation is in the reverse order of removal.
Location of Antenna AV control unit AV control unit antenna feeder In-line connectors M103, M501 Antenna amp. Window antenna Satellite radio antenna feeder Satellite radio antenna Window Antenna Repair ELEMENT CHECK Attach probe circuit tester (ohm setting) to antenna terminal on each side. When measuring continuity, wrap tin foil around the top of probe. Then, press the foil against the wire with your finger. If an element is broken, no continuity will exist. To locate a break, move probe along element. Tester indication will change abruptly when probe passes the broken point. REPAIR EQUIPMENT Conductive silver composition (DuPont No. 4817 or equivalent) Ruler 30 cm (11.
Removal and Installation REMOVAL Remove the rear pillar finisher RH. Refer to INT-23, "Exploded View". Detach the antenna amp. harness clip (A). Disconnect the harness connectors (B) from the antenna amp. (1). Remove the antenna amp. screw (C) and the antenna amp. (1). INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Remove the map lamp assembly. Refer to INL-84, "Removal and Installation". Detach the microphone connector (A). Remove the map lamp covers (1), then remove the map lamp assembly cover (2). Release the microphone tabs (A), then remove the microphone (1). INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Disconnect the battery negative terminal. Refer to PG-68, "Removal and Installation (Battery Tray)". Remove the rear parcel shelf finisher. Refer to INT-28, "Removal and Installation". Remove the Bluetooth antenna screw (A). Detach the Bluetooth antenna harness clip (B). Fold down the rear seat (if equipped) or open the trunk lid, then detach the Bluetooth antenna harness clip (C). Disconnect the harness connector (D) from the Bluetooth antenna (1) and remove. INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Disconnect the battery negative terminal. Remove the trunk upper finisher. Refer to INT-36, "Exploded View". Remove the parcel shelf finisher. Refer to INT-28, "Removal and Installation". From inside the passenger compartment, remove the bracket screws and lower the assembly for access. Remove the Bluetooth control unit screws (A). Disconnect the Bluetooth control unit connectors (B) and remove the Bluetooth control unit (1). INSTALLATION Installation is in the reverse order of removal.
Removal and Installation REMOVAL Remove the license plate finisher. Refer to EXL-166, "Removal and Installation". Remove trunk lid finisher. Refer to INT-36, "Exploded View". Disconnect the rear view camera connector (B), press the rear view camera tab (A) and remove the rear view camera (1). INSTALLATION Installation is in the reverse order of removal.
